... along with a somewhat lopsided inner skirt that also gives this piece some unique character ...
Posted by Joe Maurath, Jr. on February 16, 2012 - 0.3kb
... of the pinhole to the base of the inner skirt. This effect is somewhat less dramatic than as seen in the photo. **Priced reduced to move $75.00 ...
Posted by Joe Maurath, Jr. on February 16, 2012 - 0.4kb
... on the dome top. Big bubble in the rear skirt adds more character. Three needle point ticks, two micro 1/16" wire ridge nicks and a tiny ...
Posted by Robert W Baumann on February 16, 2012 - 0.4kb
... ) DE CHILE (Reverse). Half a pinky nail skirt flake and a few scattered teeny fleabite tic marks and light wear marks are the only damage ...
Posted by (private) on February 16, 2012 - 0.3kb
... of these lines going down the outer skirt. Most pony insulators I've seen only have two. In fact, this is the first one I know of found with ...
Posted by (private) on February 16, 2012 - 0.2kb
1/4 inch thread interval and no inner skirt ...
Posted by (private) on February 16, 2012 - 0.0kb
... 2" w x 3 3/16" ht. No inner skirt ... in a 4 piece mold as there are three skirt mold lines with cross hatch lines and presumably one piece for the dome. No inner skirt ...
Posted by (private) on February 16, 2012 - 2.2kb
... stress cracks on the lower outer skirt, No damage to any of the drips (RDP) but one drip is not formed, rounded base looks like a bubble ... down to the bottom edge of the outer skirt the width of the above logo, you can see it in the photo if you look close. $40 including shipping ...
Posted by Wesley Lirette on February 15, 2012 - 1.6kb
... One inner skirt stress crack (similiar to all the other ones), No Drip Damage. USA or Canada PayPal or Money order ... manufacture crack on the lower Inner skirt, 1/16- 1/32" split opening at the outer most part. Bottom inner skirt has a little roughness ...
Posted by Wesley Lirette on February 15, 2012 - 1.7kb
... There are 2 stress cracks on the inner skirt, the threads are melted and rough to touch. No Drip Damage. USA or Canada PayPal or Money order ... manufacture crack on the lower inner skirt, you can feel a little edge with your fingernail when you rub it along the inside. Also the inner ...
Posted by Wesley Lirette on February 15, 2012 - 1.6kb
... drips up to the base of the inner/outer skirt. No drip damage. USA or Canada PayPal or Money order accepted ... stress cracks on the lower outer skirt, 2 side by side to the right of the 19, the other to the right of the USA right where it is sand ...
Posted by Wesley Lirette on February 15, 2012 - 1.5kb
... stress crack on the inside of the skirt pretthy much the whole width of the hemingray embossed area. there are some other stress cracks in ... the inner skirt leading up the threads. No damage from dropping, just manufacture stress. NO Drip damage. some fire ...
Posted by Wesley Lirette on February 15, 2012 - 1.6kb
... from manufacture process on the inner skirt that is opened at the bottom about the width of 3 sheets of paper and goes up the insulator about 1 ... manufacture cracks on the lower skirt, but almost looks like a bubble line on one of them, you can feel a little edge with your ...
Posted by Wesley Lirette on February 15, 2012 - 1.8kb
... a small manufacture crack on the lower skirt, but almost looks like a bubble line, you can feel a little edge with your fingernail when you rub ...
Posted by Wesley Lirette on February 15, 2012 - 1.4kb
... on the dome and a few shallow inner skirt flakes ...
Posted by (private) on February 15, 2012 - 0.5kb
... chip at the base/bottom of the skirt. There's a pinky nail sized feather bruise cause by a pencil erase sized impact spot with a little ... 3 or 4 bb pings on the base and inner skirt. This sounds bad, but on this big insulator it's not that bad. Also take in to consideration how ...
Posted by Kevin Piell on February 13, 2012 - 0.6kb
... it was. It looks like a spool with a skirt, but it could also be a bushing, as there are grooves in the base that might have been used with ...
Posted by Steve McCollum on February 13, 2012 - 0.4kb
... it was. It looks like a spool with a skirt, but it could also be a bushing, as there are grooves in the base that might have been used with ...
Posted by Steve McCollum on February 13, 2012 - 0.4kb
... backside, base has a flat inside the skirt shallow chip that is about 1 inch long. Next to that there is another chip that is about 3/4 of an ... long but comes up the outside on the skirt. This chip has been resin filled. The chip at the base is fairly low on the skirt, but the area ...
Posted by Kevin Piell on February 13, 2012 - 0.5kb
... minor scuffing on the dome and lower skirt that is hard to see. One fleabite on the base and 2 or 3 fleabites overall here and there that are ... , one in the dome and one in the lower skirt. Also some nice larger bubbles throughout ...
Posted by (private) on February 13, 2012 - 0.5kb
... from a line near Tacoma, Wa . The base skirt was found by Ken Willick and was not associated with the top originally. The skirt appears to be a ...
Posted by Mike Spadafora on February 13, 2012 - 2.1kb
... factory small hole inside the inner skirt and another coming up through recessed dome to allow a wire to be shielded from the rain providing ...
Posted by (private) on February 11, 2012 - 0.8kb
... piece. Has some shallow base into skirt lines and a tight crack up through the slug embossing to just below the wire ridge. Nice whittled ...
Posted by Douglas R. Smith on February 11, 2012 - 0.5kb
... whiteish spot, along with a paper thin skirt edge chip just in front of the right mold line. Sounds worse than it is but still displays nicely. ...
Posted by Douglas R. Smith on February 11, 2012 - 0.5kb
... amber swirling all throughout the rear skirt and crown, as somewhat visible in the photo. This piece is marked with the classic "OX" ... . Nice dimple on the inside of the skirt area on this one, too ...
Posted by (private) on February 11, 2012 - 2.1kb
