CD 286.9

From Insulator Wiki (Wikilator)

(Difference between revisions)
Jump to: navigation, search
Revision as of 18:36, 16 April 2008
Bill Meier (Talk | contribs)
(Discussion)
← Previous diff
Revision as of 18:44, 16 April 2008
Bill Meier (Talk | contribs)
(Details)
Next diff →
Line 7: Line 7:
This one-of-a-kind insulators was found at the Hemingray dump (see this [http://www.insulators.com/articles/great.htm article] for details). The pinhole is not threaded, but instead has a number of raised "bumps". This one-of-a-kind insulators was found at the Hemingray dump (see this [http://www.insulators.com/articles/great.htm article] for details). The pinhole is not threaded, but instead has a number of raised "bumps".
-A picture of this insulator was discovered in an [http://reference.insulators.com/publications/view/?id=8086 article] in a 1906 book. +A picture of this insulator was discovered in a Trade Journal ''High-Tension Power Transmission'' dated 1906.
 + 
 +<!-- [http://reference.insulators.com/publications/view/?id=8086 article] -->
==Discussion== ==Discussion==

Revision as of 18:44, 16 April 2008

Contents

CD 286.9

CD 286.9
Enlarge
CD 286.9

Embossings

Westinghouse Telluride Type "C"

Details

This one-of-a-kind insulators was found at the Hemingray dump (see this article for details). The pinhole is not threaded, but instead has a number of raised "bumps".

A picture of this insulator was discovered in a Trade Journal High-Tension Power Transmission dated 1906.


Discussion

Display Rack
Enlarge
Display Rack
Test Installation
Enlarge
Test Installation
Enlargement
Enlarge
Enlargement
Overlay
Enlarge
Overlay

The use of this insulator is unknown, but there is some speculation that it was an early suspension style insulator.

The text of the 1906 article has a photo (at right) of a rack showing a CD 286.9 mounted on a pin, and states that the rack is an exhibit of the insulators that were tested. As such is not necessarily indicative of how the insulators were actually installed in use.

On the left side of the cross-arm in picture "Test Installation" on the right (also from this 1906 article), there is an insulator pictured that can't be seen distinctly. This is a picture of the insulators from the testing rack, after a snowstorm, showing the actual installation. An enlargement of the image is shown immediately below that. On the left mounted underneath the top crossarm is an insulator, almost like a ramshorn insulator, the outline of which is similar to the 286.9. The "neck" appears longer -- but details are not present to see if that extension is part of a mounting bracket of some type.

The next picture shows a shadow profile of the 286.9 overlaid on the mystery ramshorn. It looks like a very close fit -- with the exception that the top obviously doesn't go up far enough to fit into the crossarm. On the other hand, the diameter of the top in the picture appears to be slightly larger than the insulator top, which would make sense if there was a covering of some sort, perhaps a bracket that went around the glass portion, and which in turn actually made the attachment to the crossarm somehow.

Quoting from a different article

 An insulator was designed to be under-hung,
 the top of the insulator being supported 
 in an inverted cup which was to be bolted
 to the under side of the cross-arm

It is possible that the 286.9 was mounted inside of a steel casing for the top half. That would allow just the steel to be attached underneath the crossarm, hence the overlay shown of the 286.9 could well be a perfect match.


This picture doesn't contain as many insulators as are pictured on the exhibit rack, so there's nothing to say that the 286.9 is actually shown.

Personal tools

Served by www.insulators.info at March 28, 2024 05:49:01 PM in 0.21 secs.